Brake Noise and Squel
Getting rid of an annoying brake squeal and other brake noise is like trying to cure a cold. You can treat the symptoms and improve the patient’s condition. But it is virtually impossible to eliminate the underlying cause. Fortunately, brake noise is not caused by a virus. It is caused by a combination of factors that sometimes add up to create noise.
Brake squeal is really a high frequency vibration. In disc brakes, it can be caused by vibrations between the pads and the discs, the pads and calipers, or the calipers and their mounts. In drum brakes, the vibrations can originate between the shoes and drums, or between the shoes and backing plates.
We can’t say why brake noise is so annoying. It just is. To some people, it has the same effect as scraping your fingernails across a blackboard. They can’t stand it, even if it is “normal” for many vehicles today. Most people want nice, quiet brakes that stop smoothly with a reassuring “shhhhh” sound. No scraping noises. No high pitched squeals that would make a dog howl. No concerned looks or stares from passengers, other motorists or nearby pedestrians who wonder if the vehicle is going to stop or not.
Brake noise can also be worrisome to many people because they fear something is wrong with their brakes and their vehicle might not be safe to drive. Noise may indicate trouble, but the only way to know for sure is to inspect the brakes. If you find nothing amiss (no worn linings, or loose, damaged or missing parts), then you can consider any or all of the following measures to deal with the noise problem:
- Dampen the pads
- Lubricate the calipers
- Replace the caliper hardware (slides, pins or bushings)
- Replace the pads
- Resurface the rotors
- Clean the brakes (drums)
One way to quiet noisy pads is to make sure the pads fit tightly in the calipers. If the pads on a single piston caliper have mounting ears or tabs that need to be bent or hammered to hold the pad in position, make sure the pad can’t be wiggled by hand. If the pads have clips, shims or anti rattle springs, make sure the necessary hardware is in place and properly installed. If you see no such items when you inspect the brakes.
If the pads are installed correctly but are still noisy, one of the least expensive and most effective ways to quiet them is to remove the pads and install insulator shims on the backs of the pads. The shims, which are usually self-adhesive, act like little seat cushions to dampen vibrations between the pad and caliper.
Another option is to apply a noise suppressing compound to the backs of the pads. Some compounds harden to a rubber-like consistency to cushion the pads. Another good choice is to apply a moly-based dry brake lubricant to the backs of the pads. This type of lubricant is long lasting and won’t burn or wash off like brake grease can. If applying a lubricant to the backs of the pads, be careful not to get any on the front side of the pads or rotor!
QUIETING THE CALIPERS
The same approach can be used on the calipers. Cleaning and lubricating the caliper mounts can also help dampen vibrations to quiet the brakes. Vibrations here can be caused by worn or loose mounts or mounting hardware.
If the calipers are badly rusted or worn, they may have to be replaced. But in most instances, they can clean up, lubricate the mounting points and return them to service. You may have to replace the caliper slides, pins, clips and/or bushings, though, if there is too much play or looseness between the caliper and knuckle. Be sure to use a high temperature brake grease so the grease stays where it belongs.
NOISY BRAKE PADS
Some pads are noisy than others. Semi-metallic pads are typically the ones that cause the most noise problems because they are harder than non asbestos organic (NAO) pads. Their high metallic content often makes them squeal when metal rubs against metal.
The amount and type of fillers and binders in a friction material can make a big difference in the amount of noise a given set of pads or shoes produce. Ingredients such as graphite, carbon and “rubber modifieds” may be added to reduce noise. Brass is another ingredient that helps dampen noise (it also has a cleaning effect on drums and rotors). Many of the newest pads designed for quiet operation use a nonmetallic “ceramic-enhanced” formula to eliminate noise.
The design of the pads themselves can also affect the amount of noise produced. A chamfered leading edge on the pads eliminates the sharp edge so the pads will slide across the rotor without grabbing and vibrating. Slotting the pads changes the frequency at which the pads oscillate so noise can be tuned out of the brake system.
Some pads also have a special coating that transfers to the rotor surface when the pads are first used. The coating material leaves a film on the rotor that reduces noise, vibration and also rotor wear. The transfer film also makes the pads less sensitive to variations in the surface finish on the rotors.
If the original pads are too noisy and can’t be quieted by insulator shims, noise compound or grease, therefore, replacing them may be the only way to get rid of the noise.
BRAKE PAD REPLACEMENT
Some brands and grades of aftermarket brake linings are quieter than others. So you may have to experiment with several different ones to find the quietest set for a given application. But whatever you do, do not substitute asbestos or non asbestos organic (NAO) pads for semi metallic pads unless the friction material supplier says it is okay to do so. Asbestos and NAO do tend to be quieter than semi metallics but can’t withstand the heat that semi metallics can. Consequently, if you swap NAO for semi metallics in a front-wheel drive car or people carrier where the brakes run hot, it can reduce the life of the linings significantly (up to half or more!) and increase the risk of overheating and brake fade.
After you have installed the new pads, it is a good idea to break them in (unless the pads are the “fully cured” type that do not require an initial break-in period). Not breaking in a new set of pads increases your risk of pad glazing and brake noise. A driver can glaze and ruin a new set of pads if he fails to go easy on the brakes for the first 200 miles. If he overheats the brakes by mashing down on the brake pedal when stpopping, he can cook the resin in the pads before it can cure and glaze the pads.
Pads that require an initial break-in can usually be seated by making 20 to 30 easy stops from about 30 mph with at least 30 seconds between brake applications so the brake pads have enough time to cool.
Whether a new set of brake pads need to be broken-in or not, you should still test drive the vehicle to make sure the brakes are operating properly and that your efforts to eliminate the noise problem have been successful.
BRAKE DISC RESURFACING
In addition to replacing the brake pads, it may be necessary to resurface the rotors to cure a noise problem. To brake quietly, the rotors have to be in good condition, relatively smooth and flat. So if the rotors are rough, glazed or have not been finished properly, they’ll have to be resurfaced.
An easy way to check the surface finish on a disc brake is the ball point pen test. Write you name on the rotor. If the ink leaves a continuous line, the surface is smooth enough. But if the ink line is broken up into dots, the surface is too rough (or coated with grease!).
How the brake rotors are resurfaced does not matter as long as they end up with a high quality smooth finish. Bench lathes and on-car lathes are both capable of high quality finishes when used properly. But both require sharp tooling and the right feed rate and spindle speed or drive speed to produce a good finish that resists brake noise. For best results, many experts recommend using round lathe bits. These will produce a smoother finish (up to twice as smooth as a new rotor!).
To reduce the risk of brake noise during pad break-in, there are aerosol “brake silencing treatments” that can be applied to rotors to help suppress noise. These are spray-on coatings that are applied to the rotors after they have been resurfaced. Some contain microfine aluminum particles, graphite and moly that fill in the valleys on the surface of the rotors and act as a temporary lubricant to help the new pads burnish in more gradually. This not only reduces brake noise but also helps the pads develop a better cure which actually increases the coefficient of friction slightly, according to one supplier of this type of product.
One of the leading causes of brake squeal in drum brakes is brake dust inside the drum. Removing the drum and cleaning the brakes, therefore, may be necessary to eliminate this kind of noise. Use an aerosol brake cleaner or brake washer to clean the brakes. Never, ever blow out the drums with compressed air because doing so blows zillions of microscopic fibers into the air, which you certainly want to avoid if the vehicle has asbestos linings.
Another cause of brake noise in drums is poor contact between the shoes and drum. Heel and toe contact between the shoe and drum is often the culprit, and the cure is to either replace the shoes with new ones or to resurface the drum slightly to increase its inside diameter. New shoes are ground with a slight eccentric to compensate for drum wear. This moves the point of contact away from the ends of the shoes toward the middle.
Other causes of drum noise can include weak or loose hardware (replace it), and vibrations between the shoes and the raised pads on the backing plates (apply brake grease).
That about sums up the techniques for eliminating brake noise and brake squeal. The war on noise is an ongoing battle, but one that can be won.